background image

This Guide Outlines the Key Functions for a Smooth Operation:

 

A - Calibrating the CCD Camera White Point using Provided Black Media

 

B - Calibrating and Adjusting the Cutter’s Position

 

C - Designing Templates for the F-MARK2

 

D - iMark Software Overview

A - Calibrating the CCD Camera White Point using Provided Black Media
       

Chapter 16:  How to Calibrate the F-MARK2   

Starting on page 37)

 

  Launch the iMark Software

 

  Manually load the black calibration sheet. While loading the sheet note the 

 

    positioning using the iMark software camera viewer window screen. 

 

  

  

( you should only see the black sheet - nothing else should be seen)

    

 

 Initialize the CE7000 cutter making sure to select Roll 2 on the control panel 

 

  

 ( always initialize cutter with Roll 2 

)

 

 Adjust the blade to the thickness of the material being cut 

 

   

( use loupe from the accessories kit to make fine adjustments )

 

Refer to Image A

 

 

 Load the blade holder on tool position one (the slot furthest back) 

Refer to Image B

 

 Set the recommended 

Force Settings

 between 

9-12

, depending on media.

F-MARK2

Key Functions & Simplified Operation For Smooth Workflow

This quick guide works best when the following has been completed:

• Basic installation of the F-MARK2 unit as outlined in the User’s Manual instructions
• Installation of the latest version of iMark Plus Software available for downloading at:

                                                                                                              

www.graphtecamerica.com/software

 

The User’s Manual for the machine & software will guide you through the complete process.  
Please note that the Setup User’s Manual also covers a Troubleshooting Section, so in the 
event you run into issues, please refer to the manual before contacting Technical Support.

Graphtec also provides helpful Video Training Videos for the

 F-MARK2 

on our website.

Click on the QR Code below or view the tutorials at 

www.graphtecamerica.com/videos

SIMPLIFIED BASIC OPERATION WORKFLOW

The CE7000 will cut a small square.  Peel off the square from the sheet. 

You should be left with a square cut showing the white liner. 

Go back in the iMark Software and click Read Marker

Once completed, the Delta X should read a value between 

90 -120 

while the Delta Y box should read a value between 

95 - 135

Confirm the values by clicking on Set , Then click on the X to Exit, 

The X and Y values you input will be saved to the computer . 

( If the values are different, repeat calibration. Also, make sure you have sufficient lighting )

NOTE:  Camera calibration will need to be performed every time changes occur.  

                 When the computer is shut off, when the F-MARK2 is disconnected from 

                 the USB port or if the software stops communicating.

1

2

Summary of Contents for F-MARK2







Reviews: