background image

GRANT ENGINEERING (UK) LIMITED

Hopton House, Hopton Industrial Estate, Devizes, Wiltshire, SN10 2EU
Tel: +44 (0)1380 736920   Fax: +44 (0)1380 736991
Email: [email protected]   www.grantuk.com

This manual is accurate at the date of printing but will be superseded and should be disregarded if specifications and/or appearances are changed in the interests of continued product improve

-

ment. However, no responsibility of any kind for any injury, death, loss, damage or delay however caused resulting from the use of this manual can be accepted by Grant Engineering (UK) 

Limited, the author or others involved in its publication.

All good sold are subject to our official Conditions of Sale, a copy of which may be obtained on application.

© Grant Engineering (UK) Limited. No part of this manual may be reproduced by any means without prior written consent.

IMPORTANT NOTE FOR USERS

These installation instructions are intended to guide the installer 

in the installation of the Grant Combined Volumiser/Low Loss 

Header.

SPECIAL TEXT FORMATS

The following special text formats are used in these instructions 

for the purposes listed below:

! WARNING !

Warning of possible human injury as a consequence of not 

following the instructions in the warning.

! CAUTION !

Caution concerning likely damage to equipment or tools 

as a consequence of not following the instructions in the 

caution.

! NOTE !

Used for emphasis or information not directly concerned 

with the surrounding text but of importance to the reader.

Page 2

PRODUCT CODES COVERED

These instructions cover the following product codes:

Product code

Product Description

HPIDSYSLLHKIT

Grant Combined Volumiser / Low Loss Header

SERVICING

The Low Loss Header/Volumiser should be inspected at least 

every twelve months, when the heat source and/or heating 

system is serviced.

Summary of Contents for HPIDSYSLLHKIT

















Reviews: