Graf Klaro Easy SBR Instructions For Start-Up, Operation And Maintenance Download Page 43

Page: 43 / 54

9. Fault messages and rectification

43 / 54

Display

Liquid crystal display

Possible cause

Rectification

KLbasic /
KL24base

KLplus /
KL 24plus

Valve 3

failure

valve 3 error

(see maintenance instructions in Annex).

Valve 4

failure

valve 4 error

UV unit error



UV module not working



Check UV module and remaining lamp life

**error**

min. water
level



Compressed air line

leaking between control
unit and feed lifter, e.g.
due to loose hose



Check hose line for leaks

Alert flooding



Water level in 1 cham-

ber is too high



Compressed air line

blocked, e.g. due to kink
in hose



See Item 9.2



Check hose line for kinks

temperature
max.



Temperature sensor not

plugged in



Cabinet fan not working



Filters in cabinet and in

compressor are dirty



Direct sunlight on cabi-

net



The temperatures en-

tered in the Service
menu for switching on
the cooling fan and the
maximum temperature
are too high



Air compressor defec-

tive



Temperature sensor

defective



Plug temperature sensor onto rear of con-

trol unit



Check the functionality of the cabinet fan



Check air filter in cabinet



Provide site with shade



Ensure good aeration



Check air filter in air compressor



Check air compressor in manual mode



Have set temperatures checked by

maintenance company



Replace temperature sensor

**error**

temp.-sensor



No temperature sensor



Temperature sensor not

fully plugged into bush



Temperature sensor

defective



Replace sensor



Ensure a reliable connection between

control unit and temperature sensor, then
de-energise control unit for 10 sec. and
switch on again, check whether a temp.
sensor fault message is displayed.

Power failure

**error**

power failure



Power cut



System switched off via

maintenance switch



Switch cabinet is not

energised



FI fuse has blown



Wait for power to be restored



Switch system back on via maintenance

switch



Check supply line to switch cabinet



Establish cause for earth leakage circuit

breaker blowing and remedy (possible
cause: solenoid valve defective).



Summary of Contents for Klaro Easy SBR























































Search results

Summary of Contents for Klaro Easy SBR

Reviews:

Related manuals for Klaro Easy SBR

Brands by name

Popular brands

Graf Klaro Easy SBR, Instructions For Start-Up, Operation And Maintenance

Search results

Summary of Contents for Klaro Easy SBR

Reviews:

Related manuals for Klaro Easy SBR

Brands by name

Popular brands