background image

Installation

334513A

21

Choosing an Installation 
Location

Select a location that will adequately support the 
weight of the pump, as well as all plumbing and 
electrical connections.

Refer to the mounting hole layout provided in 

Dimensions

 starting on page 49.

Always mount the pump upright.

If you have a mounting configuration that requires 
installation in a manner different than depicted in 
F

IG

. 2, please contact your Graco distributor for 

assistance.

Fluid Connections

1.

Remove and discard plugs on check valves. 

2.

Connect a 1/4 npt(f) fluid line from the fluid source to 
the inlet check valve (K). See F

IG

. 2 on page 20.

3.

Install a pressure relief valve (F) on the outlet side of 
the pump. 

NOTE:

 The pressure relief valve is available from Graco 

and can be connected back to the tank or directly to the 
inlet side of the pump. See 

Kits and Accessories

 on 

page 48.

4.

Set the pressure relief valve at or below the maxi-
mum working pressure of the pump.

5.

Connect a 1/4 npt(f) fluid line from the outlet check 
valve (L) to the injection point.

6.

Connect a 10-32 UNF fluid outlet from the 
prime/bleed valve (21) to the fluid source or waste 
reservoir.

In the event of an injection line blockage, to reduce the 
risk of skin injection and damage to the pump, ensure 
the pressure relief valve is set at or below the maxi-
mum working pressure of the pump.

Summary of Contents for Wolverine Series





















































Reviews: