background image

Warning

309476B

3

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury. 

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately. 

Do not exceed the maximum working pressure of the lowest rated system component. Refer to the 

Technical Data

 on page 26 for the maximum working pressure of this equipment. 

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the 

Techni-

cal Data

 section of all equipment manuals. Read the fluid and solvent manufacturer's warnings.

Do not use hoses to pull equipment. 

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose 
Graco hoses to temperatures above 82

°

C (180

°

F) or below -40

°

C (-40

°

F). 

Wear hearing protection when operating this equipment.

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

PRESSURIZED EQUIPMENT HAZARD

Spray from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin and 
cause serious injury.

Do not point the gun at anyone or at any part of the body.

Do not stop or deflect leaks with your hand, body, glove, or rag.

Follow  the 

Pressure Relief Procedure

 on page 9 whenever you are instructed to relieve pressure; 

stop spraying; clean, check, or repair the equipment; and install or clean the spray nozzle.

Tighten all fluid connections before operating the equipment.

Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately. 
Permanently coupled hoses cannot be repaired; replace the entire hose.

Summary of Contents for TRITON 1030HP































Reviews: