Graco TRITON 1030HP Instructions-Parts List Manual Download Page 26

Page: 26 / 30

Technical Data

309476B

Technical Data



Category

Data

Maximum fluid working pressure

1.8 MPa, 18 bar (260 psi)

Maximum air input pressure

0.6 MPa, 6 bar (88 psi)

Ratio

3:1

Maximum recommended flow rate (continuous duty)

7.6 liters/min (2.0 gpm)

Maximum recommended cycle rate

20 cycles/minute

Maximum flow rate

114 liters/min (30 gpm)

Volume per cycle (double stroke)

350 cc/cycle (11 oz/cycle)

Operating temperature range

10-80

C (50-176

Dry suction lift

2.5 m (8.2 ft)

Wet suction lift

6.7 m (22 ft)

Air inlet size

Model 233750:

1/2 BSPP(f)

Model 233751:

1/2 npt(f)

Fluid inlet size

Model 233750:

1 in. BSPP(f)

Model 233751:

1 in. npt(f)

Fluid outlet size

Model 233750:

1 in. BSPP(f)

Model 233751:

1 in. npt(f)

Noise level at 15 cycles/min, 0.6 MPa, 6 bar (88 psi) air
inlet pressure. Tested per ISO 9614-2.

66 dB(A)

Weight (approximate)

29 kg (64 lb)

Wetted parts

301 and 316 stainless steel, acetal, fluorocarbon,
ultra-high molecular weight polyethylene,



, A4

stainless steel (233750 only)

PTFE

Summary of Contents for TRITON 1030HP































Search results

Summary of Contents for TRITON 1030HP

Reviews:

Related manuals for TRITON 1030HP

Brands by name

Popular brands

Graco TRITON 1030HP, Instructions-Parts List Manual

Search results

Summary of Contents for TRITON 1030HP

Reviews:

Related manuals for TRITON 1030HP

Brands by name

Popular brands