background image

Installation

3A8626C

9

Pressure Relief Procedure

Follow the Pressure Relief Procedure whenever 

you see this symbol.

1. Turn off the power supply to the pump or close the 

upstream ball valve.

2. Trigger the dispense valve into a waste container to 

relieve pressure.

3. Open any bleed-type master air valves and fluid 

drain valves in the system.

4. Leave the drain valve open until ready to pressurize 

the system.

NOTE: If you suspect that the dispense valve or 

extension is clogged, or that the pressure has not been 

fully relieved after following the above steps, very 

slowly loosen the coupler or hose end coupling to 

relieve the pressure gradually, then loosen completely. 

After doing this, the obstruction can be cleared.

Flush the Equipment

Before installation of the dispense valve to the end of 

the hose, flush the line with the fluid being dispensed.

1. Place the end of the hose into a grounded metal 

waste container. Hold the hose firmly against the 

waste container throughout the flushing process 

(F

IG

. 2).

This equipment stays pressurized until pressure is 

manually relieved. To help prevent serious injury from 

pressurized fluid, such as skin injection, splashing 

fluid and moving parts, follow the Pressure Relief 

Procedure when you stop dispensing and before 

cleaning, checking, or servicing the equipment.

To avoid fire and explosion, always ground 

equipment and waste container. To avoid static 

sparking and injury from splashing, always flush at 

the lowest possible pressure. 

F

IG

. 2

Summary of Contents for SDL23 Series























































Reviews: