background image

Service 

20

311189L

EasyKey™ Display

Updating Software

Replacing Power Supply Board

Replacing Power Supply Fuses

Updating Software

There are 2 ways to update software:

Programmed software chip 249943 or Kit 249989. 
Kit includes display board software chip, chip 
extractor tool, and grounding wrist strap. 

Follow 

Installing New Software Chip

 procedure. 

Installing New Software Chip

1.

Follow 

Before Servicing

 procedure, page 18.

2.

Unlock and open EasyKey™ door with its key.

3.

Remove display board chip (C - F

IG

. 15) with 

removal tool.

a.

Press removal tool into flash chip socket open 
holes.

b.

Squeeze the tool to grip the chip and carefully 
pull it straight out of the socket.

4.

Align beveled corner of new chip with beveled 
corner of socket and press chip into place. Make 
sure the pins are not bent or touching.

5.

Close and lock EasyKey™ door with key.

6.

Turn EasyKey™ power on to test circuit boards.

NOTE: If you need to replace the EasyKey

 dis-

play board, display backlight, or keypad, 
replace with Display Kit 253025.

CAUTION

To avoid damaging circuit board when servicing, wear 
grounding strap on wrist and ground appropriately.

F

IG

. 15

C

Summary of Contents for ProMix Auto Series

















































Reviews: