background image

Parts 

20

309572M

15F144 Hose Wire Jumper

Use the 15F144 Hose Wire Jumper to heat 
only the major volume hose, in a wide ratio 
system.

To build one complete 50 ft single side heated 
hose bundle, order the following parts:

Install as follows:

1. Wrap hose wire jumper (100) around resin 

hose (101) in a spiral fashion.

2. Connect resin hose wire (101a) to other 

side of Power-Lock connector (100a); see 
page 9.

3. Wrap FTS cable (102) around resin hose 

(101) in a spiral fashion.

4. Twist hoses (101 and 105) together to pro-

vide strain relief.

5. Repeat steps 1-4 for each length of hose 

(101). Connect hoses, electrical connec-
tors, and cables; see Connect Heated 
Hoses
, page 9.

6. Install one Power-Lock connector (100a) 

between wires; see page 9.

Ref. Part

Description

Qty

100

15F144

JUMPER, hose wire; includes 
two 117789 electrical connec-
tors; 50 ft (15.2 m) long

1

101

chart 2, 
page 19

HOSE, resin, heated; 50 ft 
(15.2 m) minimum

1

102

15B296

CABLE, FTS

1

103

15C517

HARNESS, hose jumper

1

104

261670

FLUID TEMPERATURE 
SENSOR; see page 18

1

105

purchase 
locally

HOSE, hardener, unheated; 50 
ft (15.2 m) minimum; customer 
supplied

1

106

purchase 
locally

CONNECTORS, fluid; as 
required to complete assem-
bly; not shown

as

req’d

WARNING

Read warnings, pages 6 and 7.

Hoses (101 and 105) must be sized and 
pressure rated to meet the requirements of 
your system.

Do not operate heated hose (101) at more 
than 45 A. If hose is cold, turn current adjust-
ment fully counterclockwise before reheating 
hose.

Spray gun must be grounded.

Summary of Contents for Power-Lock

























Reviews: