background image

Repair 

16

3A5266G

18. Inspect pump base (2) casting for scratches and 

scoring. If excessive damage is found, replace 

pump.

Pump Lower Reassembly

See Oil and Grease Parts, pages 18 and 20.

NOTE:

 

Pump Lower Soft Seal Kit 17T654 is available (see page 

30). Parts marked with ‡.
Hard Parts and Seal Kit 17T655 is available (see page 

30). Parts marked with 

.

For best results, use all of the parts in the kit.
1. Press bearing (5

) into the pump cylinder (11

).

2. Install two o-rings (6‡

) around pump cylinder 

(11

).

3. Install shovel seal retainer (10

) on piston shovel 

rod (12

).

4. Lubricate o-ring (7‡

) and install on the end of the 

shovel seal retainer (10

).

5. Install intake seal (17‡

) on the shovel rod (12

(F

IG

. 21)

NOTE:

 When installed correctly the flat end of the 

intake seal (17‡

) meets the flat surface of the 

shovel rod retainer (10

). The jagged end of the 

intake seal will be facing the piston rod (19).

6. Install piston seal (18‡

) to piston rod (19

).

7. Clean threads of piston rod (19

) and alignment 

rod (13

) with solvent to prepare it for thread lock

-

ing compound (F

IG

. 21)

8. Apply oil resistant, thread locking compound (user 

supplied) to threads of piston rod (19

) and align

-

ment rod (13

). Screw the two rods together. 

Torque to 25-35 ft-lbs (34 to 47.5 N•m).

NOTE:

 

- It may be easier to assemble the two parts by 

clamping the piston rod in a vise. Take care 

when clamping the rod in vise to not 

over-tighten the vise around the rod which 

could damage the rod or scratch the outside 

surface. Clamp only on recessed surface of 

piston rod (19).

- If using a vise, to prevent the rod from rotating 

while torquing the two parts. insert a pin that is 

longer than the spring pin (20) through the pin 

holes.

9. Screw shovel rod (12

) into piston rod (19

). 

Tighten until pin holes in each rod (F

IG

. 21) align.

10. Install spring pin (20‡

) through holes aligned in 

Step 6 (F

IG

. 21).

11. Install piston rod (19

) and shovel rod (12

assembly inside pump cylinder (11

).

12. Install bearing (5

) in seal retainer (9

).

13. Lubricate wiper seal (4‡

) and install in the seal 

retainer (9

). 

NOTE:

 The lips of the wiper seal (4‡

) should be 

facing out; toward the piston shovel rod (12

).

14. Lubricate o-ring (6‡

) and install o-ring around the 

seal retainer (9

).

15. If the H-wiper seal (3‡

) was removed in Pump 

Lower Disassembly, Step 7, page 15, lubricate new 

seal from kit and install it in pump base (2).

NOTE:

 The lips of the H-wiper seal (3‡

) should be 

facing in; toward the pump cylinder (11

).

F

IG

. 21

20

18

12

10

6

17

13

19

7

F

IG

. 22

3‡

11

Summary of Contents for LubePro A4000







































Reviews: