Graco LubePro A4000 Instructions Manual Download Page 30

Page: 30 / 38

Air Motor Parts

3A5266G

Complete Air Valve Replacement Kit 24A351

To replace the complete air valve, order Air Valve Replacement Kit 24A351.

The kit includes items 301-312 below, and items 209 and 211 on page 30.Air Valve Repair Kits

Air valve parts are not sold individually.

The table below shows possible kit options for each part.

† Included in Air Valve Seal Kit 24A535.

◆

Included in Air Valve Repair Kit 24A537.

✚

Included in Air Valve End Cap Kit 24A360.

Replacement screws (309) are available in a pack of 10. Order Kit 24A359.

Ref.

Description

Qty.

Air Valve

Repair Kit

24A537

Air Valve

Seal Kit

24A535

Air Valve

End Cap Kit

24A360

301

HOUSING

302

◆

AIR VALVE PISTON

303

◆

DETENT PISTON ASSEMBLY

304

◆

DETENT CAM

305

◆

PLATE, air valve

306†

✚◆

O-RING

307

✚

CAP

308†

◆

U-CUP

309†

◆

SCREW

310

✚

SNAP RING

311

◆

DETENT SPRING

312

◆

CUP

Summary of Contents for LubePro A4000







































Search results

Summary of Contents for LubePro A4000

Reviews:

Related manuals for LubePro A4000

Brands by name

Popular brands

Graco LubePro A4000, Instructions Manual

Search results

Summary of Contents for LubePro A4000

Reviews:

Related manuals for LubePro A4000

Brands by name

Popular brands