manualshive.com logo in svg

Graco LineLazer IV 3900, Repair Parts List Manual

Share
Download
Graco LineLazer IV 3900 Repair Parts List Manual Download Page 18

Pressure Control 

18

312195B

Control Board

Removal

1.

Relieve pressure, page 6.

2.

F

IG

. 13. Remove two screws (125) and control cover 

(31). Pull display connector wings open on control 
board and pull display connector out.

3.

F

IG

. 13 and F

IG

. 21. Note on a paper lead connec-

tions to the control board. Disconnect leads from 
control board (15d). 

4.

F

IG

. 13. Remove five screws (15j) from control 

board (15d).

Installation

1.

F

IG

. 13.  Install control board (15d) with five screws 

(15j).

2.

F

IG

. 13 and F

IG

. 21. Refer to note on lead connec-

tions to the control board. Connect leads to control 
board (15d).

3.

F

IG

. 13. Push display connector into control board 

close display connector wings on control board. 
Install control cover (31) with two screws (125).

Pressure Control Transducer

Removal

1.

Relieve pressure, page 6.

2.

F

IG

. 13. Remove two screws (125) and control cover 

(31).

3.

Disconnect transducer lead (C) from control board 
(15d).

4.

Remove pressure control transducer (216) and 
o-ring (217) from filter manifold (40).

Installation

1.

F

IG

. 13. Install o-ring (217) and pressure control 

transducer (216) in filter manifold (40). Torque to 
35-45 ft-lb.

2.

Connect transducer lead (C) to control board (15d).

3.

Install control cover (31) with two screws (125).

Pressure Adjust Potentiometer

Removal

1.

Relieve pressure, page 6.

2.

F

IG

. 13. Remove two screws (125) and control cover 

(31).

3.

Disconnect lead (D) from control board (15d).

4.

Loosen set screws on potentiometer knob (15o) and 
remove knob, shaft nut, lockwasher and pressure 
adjust potentiometer (15i).

5.

Remove seal (15n) from potentiometer (15i).

Installation

1.

Install seal (15n) on potentiometer (15i).

2.

F

IG

. 13. Install pressure adjust potentiometer (15i), 

shaft nut, lockwasher and potentiometer knob (15o).

a.

Turn potentiometer shaft (15i) clockwise to inter-

nal stop. Assemble potentiometer knob (15o) to 

strike pin on plate (15r).

b.

After adjustment of step a, tighten both set 

screws in knob 1/4 to 3/8 turn after contact with 

shaft.

3.

Connect lead (D) to control board (15d).

4.

Install control cover (31) with two screws (125).

Summary of Contents for LineLazer IV 3900







































Reviews:

No comments

Brands by name

Popular brands

Load more brands