background image

Installation 

12

3A8637B

Installation

Grounding

Ground individual components by any of the following 
methods: 

Mount the component to a grounded conductive 
surface.

Connect conductive fluid tubes to the component.

Connect a ground wire to one of the component’s 
mounting holes.

Flush Before Using Equipment

The equipment was tested with lightweight oil, which is 
left in the fluid passages to protect parts. To avoid 
contaminating your fluid with oil, flush the equipment 
with a compatible solvent before using the equipment. 
See your proportioner manual for details.

Color Change Stack

Assemble a Color Change Stack

1.

Lubricate the o-ring (4) and insert it in the housing’s 
valve port.

NOTE: 

This procedure is for the Quick Socket version of 

the color change stack kits, which connects the color 
change stack to non-IniFlex components. The IniFlex 
version of the color change stack kits includes a 
disposable shipping plug instead of the adapter 
connector (7), and is directly connected to other 
components with IniFlex fittings. The adapter connector 
(7) and shipping plug both connect to the tie rods (8) 
and hold the color change stack together during 
shipping.

2.

Install the valve (5) in the valve port and torque to 
50 in-lbs (5.6 N•m).

3.

Repeat steps 1 and 2 for each valve in your color 
change stack.

NOTE: 

The maximum number of valves in a color 

change stack is 18.

4.

Line up the adapter connector (7) and assembled 
valves (including seals (3) and tie rods (8) in order 
of installation, with the valve closest to the adapter 
connector being first. Verify that the assembled 
valves are oriented with the fluid outlets directed 
towards the adapter connector (7), and that each 
fluid outlet has an o-ring (2) attached to it.

5.

Assemble the segments for each tie rod (8) and 
hand-tighten.

The equipment must be grounded to reduce the risk 
of static sparking. Static sparking can cause fumes to 
ignite or explode. Grounding provides an escape wire 
for the electric current. 

F

IG

. 1: Color change stack assembly

4

5

7

8

2

3

6

9

Summary of Contents for IniFlex































Reviews: