Graco Husky 515 D51 Series Instructions Manual Download Page 36

Page: 36 / 38

308981

Husky 515 and 716 Performance Charts

Air Consumption

Test Conditions

: Pump tested in water with inlet submerged.

(7.6)

(15.2)

(22.7)

(30.3)

(37.9)

(45.4)

(53.0)

(60.6)

(0.28)

(0.14)

(0.42)

(0.56)

(0.70)

(0.84)

AIR CONSUMPTION- -scfm (cubic meters/min)

Air Consumption Curves

at 100 psi (0.7 MPa, 7 bar) air pressure

at 70 psi (0.48 MPa, 4.8 bar) air pressure

at 40 psi (0.28 MPa, 2.8 bar) air pressure

FLUID FLOW- -gpm (lpm)

To find Pump Air Consumption

(scfm or m#/min) at a

specific fluid flow (gpm/lpm) and air pressure

(psi/MPa/bar):

1. Locate fluid flow rate along bottom of chart.

2. Read vertical line up to intersection with selected air

consumption curve.

3. Follow left to scale to read air consumption.

Summary of Contents for Husky 515 D51 Series







































Search results

Summary of Contents for Husky 515 D51 Series

Reviews:

Related manuals for Husky 515 D51 Series

Brands by name

Popular brands

Graco Husky 515 D51 Series, Instructions Manual

Search results

Summary of Contents for Husky 515 D51 Series

Reviews:

Related manuals for Husky 515 D51 Series

Brands by name

Popular brands