Graco Husky 1040 FDA Instructions-Parts List Manual Download Page 41 | Manualshive

Page: 41 / 51

background image

Performance Chart - 1590

309528L

41

Performance Chart - 1590

Example of Finding Pump Air Consumption and Air Pressure at a Specific Fluid Delivery and Discharge
Head: To supply 60 gpm (227 liters) fluid flow (horizontal scale) at 40 psi (0.28 MPa, 2.8 bar) discharge head pres-

sure (vertical scale) requires approximately 50 scfm (1.4 m

3

/min) air consumption at 70 psi (0.49 MPa, 4.9 bar) inlet

air pressure.

Test Conditions: Pump tested in water with
PTFE diaphragm and inlet submerged

Key:
A, B, C, D Fluid pressure and flow
E, F, G, H scfm air consumption

«
...
39
40
41
42
43
...
»

Summary of Contents for Husky 1040 FDA




















































Reviews:

No comments

Related manuals for Husky 1040 FDA

Brand: Zip Pages: 12

Brand: York Pages: 204

Brand: GEA Pages: 337

Brand: PAPILLON Pages: 16

LARIUS SIRIO 60:1

Brand: Samoa Pages: 46

Brand: clage Pages: 24

Brand: Daikin Pages: 44

Brand: YAMADA Pages: 25

Brand: A.O. Smith Pages: 2

Brand: A.O. Smith Pages: 24

Brand: YAMADA Pages: 12

HAWK LEUCO TXT Series

Brand: Kärcher Pages: 36

Brand: Quincy Compressor Pages: 42

Brand: Klima hitze Pages: 39

THERMOSIPHON 150/2.5

Brand: SUN&HEAT Pages: 38

Thermo Pro 90 HDD

Brand: Webasto Pages: 6

Brand: Graco Pages: 20

Brand: Alpha-InnoTec Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands