background image

Technical Data - 1040

 

32

309528L

Technical Data - 1040

Santoprene® is a registered trademarks of the Monsanto Co.

Loctite® is a registered trademark of the Loctite Corporation.

*Displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type.

**Noise levels measured with the pump mounted on the floor, using rubber feet. Sound power measured per
ISO Standard 9614-1.

***The pump user must verify that the construction materials meet their specific application requirements.

Maximum fluid working pressure  . . . . . . . . . . . . . . . . . . . 120 psi (0.8 MPa, 8 bar)

Air pressure operating range  . . . . . . . . . . . . . . . . . . . . . . 20-120 psi (0.14-0.8 MPa, 1.4-8 bar)

Maximum air consumption . . . . . . . . . . . . . . . . . . . . . . . . 60 scfm

Air consumption at 70 psi/20 gpm  . . . . . . . . . . . . . . . . . . 20 scfm (see chart)
Maximum free-flow delivery  . . . . . . . . . . . . . . . . . . . . . . . 42 gpm (159 l/min)

Maximum pump speed . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 cpm

* Gallons (Liters) per cycle . . . . . . . . . . . . . . . . . . . . . . . . 0.15 (0.57)
Maximum suction lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 ft (5.48 m) wet or dry
Maximum size pumpable solids . . . . . . . . . . . . . . . . . . . . 1/8 in. (3.2 mm)

** Maximum Noise Level at 100 psi, full flow  . . . . . . . . . .   89 dBa

** Sound Power Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 dBa

** Noise Level at 70 psi and 50 cpm. . . . . . . . . . . . . . . . . 78 dBa

Maximum fluid operating temperature is based on the fol-
lowing maximum diaphragm, ball, and seat temperature 
ratings.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PTFE 220°F (104.4°C)
Santoprene® 180°F (82.2°C)
Buna-N 180°F (82.2°C)
fluoroelastomer 250°F (121.1°C)
Stainless steel 250°F (121.1°C)

Air inlet size  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5” npt(f)
Fluid inlet size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5” sanitary flange

Fluid outlet size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5” sanitary flange
Wetted parts
***All fluid contact materials are FDA-compliant and meet the United States Code of Federal Regulations (CFR) 
Title 21, Section 177.

All fluid contact materials are FDA-compliant.
Wetted materials on all models  . . . . . . . . . . . . . . . . . . . .
Wetted material depending on model. . . . . . . . . . . . . . . .

316 SST, PTFE
316 SST, PTFE, Santoprene®, Buna-N (Nitrile), fluo-
roelastomer

Note: Santoprene® may be used only with non-fatty, non-oily foods or alcohols up to 15%.

Non-wetted external parts  . . . . . . . . . . . . . . . . . . . . . . . .

painted aluminum, 300 series stainless steel, polyester 
(labels), Santoprene® (gasket), LDPE foam (gasket)

Weight

Models with aluminum center sections. . . . . . . . . . . . . . . 34 lb. (16.0 kg)

Models with stainless steel center sections . . . . . . . . . . . 47 lb. (22.0 kg)

Summary of Contents for Husky 1040 FDA




















































Reviews: