background image

Parts

309834W

11

Parts

Model 246190, HG6000 Meter

* Included in Gear Replacement Kit 246596.

† Included in Bearing Replacement Kit 253215.

Not shown.

1

2

Torque to 350 +/- 15 in-lb (39.5 +/- 1.7 N•m)

Torque to 42 +/- 15 in-lb (4.75 +/- 1.7 N•m)

2

5

6

5

15

16

17

16

20

19

18

13

7

6

9

4

3

17

23

1

3

After ball (6) is placed into bearings, 
apply grease (31) into bearing area. 

3

24

22

21

7e

1

15

5

6

7e

8

7c

7d

7f

7b

7a

7e

2

3

1

3

2

r_246190_309834_3r

Ref. Part

Description

Qty.

1

HOUSING, end 

1

2

117535 SCREW, cap, socket head 

6

3

GUIDE, gear

1

4†

INSERT, bearing 

1

5†

246594 BEARING, gear (includes 4)

3

6†

101680 BALL, bearing

3

7*

234052 GEAR, sub-assembly; 2-tooth 

(includes 7a-7f)

1

7a

GEAR

1

7b

ROD, gear

1

7c

GEAR, spur

1

7d

GUIDE, rod

1

7e

ROD, gear

3

7f

BEARING

1

8*

234053 GEAR, sub-assembly; 3-tooth 

(includes 7e)

1

13*

SPACER, shaft, gear

1

15†

INSERT, bearing

2

16*† 117541 SEAL

2

17†

PIN, dowel, 0.75 in.

2

18†

HOUSING, middle

1

19

CAP, end

1

20

117536 SCREW, cap, socket head

6

21

24U114 SENSOR, Model 246190 only

1

239717 SENSOR, Model 280560 only

1

22

15B413 PAD, sensor

1

23

114100 SCREW, cap, socket head 

2

24

106371 SCREW, mach, hex flat head 

2

31†

LUBRICANT, grease

1

Ref. Part

Description

Qty.

Summary of Contents for HG6000





















Reviews: