background image

2

308266

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

WARNING

SKIN INJECTION HAZARD

High–pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like
just a cut, but it is a serious injury that can result in amputation. 

Get immediate surgical treatment.

D

Do not point dispense valve at anyone or at any part of the body.

D

Do not put your hand over the end of the dispense nozzle.

D

Do not stop or deflect leaks with your hand, body, glove, or rag.

D

Follow 

Pressure Relief Procedure

 in this manual, when you stop spraying and before cleaning,

checking, or servicing equipment.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

D

Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See 

Technical Data

 in all equipment manuals.

D

Use fluids and solvents that are compatible with equipment wetted parts. See 

Technical Data

 in all

equipment manuals. Read fluid and solvent manufacturer’s warnings.

D

Check equipment daily. Repair or replace worn or damaged parts immediately.

D

Do not alter or modify equipment.

D

For professional use only.

D

Use equipment only for its intended purpose. Call your Graco distributor for information.

D

Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

D

Do not use hoses to pull equipment.

D

Comply with all applicable safety regulations.

Summary of Contents for DynaMite 224906















Reviews: