background image

Troubleshooting

308360D

11

Troubleshooting

1. Follow 

Pressure Relief Procedure

, page 8, before 

checking or repairing the pump.

2. Check all possible problems and causes before 

disassembling pump.

To determine if the fluid hose or gun is obstructed:

1. Perform the 

Pressure Relief Procedure

, page 8. 

2. Disconnect the fluid hose and place a container at 

the pump fluid outlet to catch any fluid.

3. Turn on the air just enough to start the pump. If the 

pump starts when the air is turned on, the 
obstruction is in the fluid hose or gun.

NOTE: 

If you experience air motor icing, call Graco 

Technical Assistance.

Problem

Cause

Solution

The pump fails to operate.

The air line is restricted or the air 
line is inadequate; valves are closed 
or clogged.

Clear the line; increase the air 
supply. Check that the valves are 
open.

The fluid hose or gun is obstructed; 
the fluid hose ID is too small.

Open, clear*; use a hose with a 
larger ID.

Fluid has dried on the displacement 
rod.

Clean the rod; always stop the pump 
at the bottom of its stroke; keep the 
wet-cup 1/3 filled with a compatible 
solvent.

Motor parts are dirty, worn, or 
damaged.

Clean or repair; see the separate 
motor manual.

The pump operates, but the output 
is low on both strokes.

The air line is restricted or the air 
line is inadequate; valves are closed 
or clogged.

Clear the line; increase the air 
supply. Check that the valves are 
open.

The fluid hose or gun is obstructed; 
the fluid hose ID is too small.

Open, clear*; use a hose with a 
larger ID.

The packings in the displacement 
pump are worn.

Replace the packings.

The pump operates, but the output 
is low on the downstroke.

The intake valve is held open or 
worn.

Clear the valve; service.

The pump operates, but the output 
is low on the upstroke.

The piston valve or packings are 
held open or worn.

Clear the valve; replace the 
packings.

Erratic or accelerated pump speed.

The fluid supply is exhausted.

Refill the supply and prime the 
pump.

The piston valve or packings are 
held open or worn.

Clear the valve; replace the 
packings.

The intake valve is held open or 
worn.

Clear the valve; service.

Summary of Contents for Dura-Flo 1200



























Reviews: