Graco Dura-Flo 1200 Instructions Manual Download Page 1

Page: 1 / 26

308360D

Instructions

Dura-Flo

1200 Pumps

Stainless Steel

For dispensing non-corrosive and non-abrasive oils and lubricants only. For professional
use only.

237516 Pump, Series A, 21:1 Ratio,
with Bulldog

Air Motor

2100 psi (14.5 MPa, 145 bar) Maximum Fluid Working
Pressure

100 psi (0.7 MPa, 7 bar) Maximum Air Input Working
Pressure

237517 Pump, Series A, 13:1 Ratio,
with Senator

Air Motor

1300 psi (9 MPa, 90 bar) Maximum Fluid Working
Pressure

100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Working
Pressure

See page 24 for model information, including maximum
working pressure and approvals.

Important Safety Instructions

Read all warnings and instructions in this
manual before using the equipment.
Save these instructions.

04140

04143

Model 237517

Model 237516

II 2 G

Summary of Contents for Dura-Flo 1200



























Search results

Summary of Contents for Dura-Flo 1200

Reviews:

Related manuals for Dura-Flo 1200

Brands by name

Popular brands

Graco Dura-Flo 1200, Instructions Manual

Search results

Summary of Contents for Dura-Flo 1200

Reviews:

Related manuals for Dura-Flo 1200

Brands by name

Popular brands