Graco Bulldog 221-104 Instructions-Parts List Manual Download Page 11

 

Dimensions

Mounting Hole Layout

4”

(102 mm)

2”

(51 mm)

3.46”

(88 mm)

3.71”

(94 mm)

1.875” (48mm)

For Outlet

Riser Tube

0.44”
(11.1 mm)
dia. (4)

3.71”

(94 mm)

5/8 UNC

(3) For Pump

Attachment

11” (279 mm) 
Diameter

2.218” (56.3 mm) 
Diameter

57.75”

(1365 mm)

21.25”

(540 mm)

32.5”

(826 mm)

Technical Data

Air operating range

30 psi (2.1 bar, 210 KPa) min. to 100 psi (7 bar, 700 KPa) max.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Maximum fluid pressure

500 psi (35 bar, 3.5 MPa) at a maximum 100 psi (7 bar, 700 KPa) air input

. . . . . . . . . . . . . . . 

Air consumption

5.3 CFM (0.15 m

#

) at 1 gallon (3.78 l) at 100 psi (7 bar, 700 KPa) air input

. . . . . . . . . . . . . . . . . . . . . . 

Cycles per gallon (liter)

3.3 (0.87)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Maximum recommended pump speed

60 cycles/min

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Air inlet size

3/4 npt

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Fluid outlet size

1–1/2” npt

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Fluid inlet size

2” npt

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Wetted parts

Intake and Riser Tubes: Zinc-Plated Steel,

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Displacement Pump: See Manual 308–043

Manual Change Summary

The following changes were added to this manual:

D

    The entire manual was revised electronically.

D

    The manual was updated to include the changes fom PCN E.

Summary of Contents for Bulldog 221-104













Reviews: