background image

2

309016

Table of Contents

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operation

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Troubleshooting

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Pump Service

Model 804594 (DD6814)

12

. . . . . . . . . . . . . . . . . . . . . . 

Models 804596 (DD9023) & 804597 (DD9021)

14

. . . 

Parts Drawings and Lists

Model 804594 (DD6814)

16

. . . . . . . . . . . . . . . . . . . . . . 

Models 804596 (DD9023) & 804597 (DD9021)

18

. . . 

Pump Repair Kits

20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Warranty

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Phone Number

22

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.

WARNING

INJECTION HAZARD

Spray from the gun, leaks, or ruptured components can inject fluid into your body and cause serious
injury.  Fluid splashed in the eyes or on the skin can also cause serious injury.

D

Fluid injected into the skin might look like just a cut, but it is a serious injury.  

Get emergency

medical attention.

D

Do not point gun at anyone or at any part of body.

D

Do not stop or deflect leaks with hand, body, glove, or rag.

D

Do not put hand or fingers over spray tip.

D

Tighten fluid connections before starting equipment.

D

Engage the gun trigger safety whenever you stop spraying.

D

Follow 

Pressure Relief Procedure on page 5 if spray tip clogs and before cleaning, checking, or

servicing equipment.

D

Repair or replace worn or damaged parts immediately.

D

Check hoses, tubes, and coupling daily.  Do not repair high-pressure couplings: replace entire
hose.  Fluid hoses must have spring guards on both ends to prevent kinks and rupture.

Summary of Contents for AquaMax 804594 A Series























Reviews: