background image

Warnings 

4

3A8693B

PRESSURIZED EQUIPMENT HAZARD

Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin and cause 
serious injury.

Follow the Pressure Relief Procedure when you stop spraying/dispensing and before cleaning, 
checking, or servicing equipment. 

Tighten all fluid connections before operating the equipment.

Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

PRESSURIZED ALUMINUM PARTS HAZARD

Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical 
reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or 
property damage.

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or 
fluids containing such solvents.

Do not use chlorine bleach.

Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier 
for compatibility.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or 
swallowed.

Read Safety Data Sheets (SDSs) to know the specific hazards of the fluids you are using.

Route exhaust away from work area. If diaphragm ruptures, fluid may be exhausted into the air.

Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

BURN HAZARD 

Equipment surfaces and fluid that is heated can become very hot during operation. To avoid severe 
burns:

• Do not touch hot fluid or equipment.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including 
eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not 
limited to:

Protective eyewear, and hearing protection. 

Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

WARNING

Summary of Contents for Aluminum Husky 2150 LP



































Reviews: