background image

Troubleshooting 

14

3A8693B

Troubleshooting

1.

Follow Pressure Relief Procedure, page 12, 
before checking or repairing the equipment.

2.

Check all possible problems and causes before 
disassembling equipment.

Problem

Cause

Solution

Equipment cycles at stall or 
fails to hold pressure at 
stall.

Worn check valve flappers (116), seats (115) 
or gaskets (112, 114).

Replace. See page 16.

Equipment will not cycle, or 
cycles once and stops.

Air valve is stuck or dirty.

Disassemble and clean air valve. See 
page 21. Use filtered air.

Check valve flapper (116) is stuck.

Replace flapper and seat. See 
page

 16.

Check valve flapper (116) is stuck due to 
overpressurization.

Install Pressure Relief Valve. See 
page

 11.

Dispensing valve clogged.

Relieve pressure and clear valve.

Equipment cycles but will 
not prime or no flow.

Excessive suction lift.

Ensure the suction lift does not exceed 
the maximum listed in Technical 
Specifications
, page

 

32. To aid with 

priming, fill the chambers with liquid.

Equipment operates 
erratically.

Clogged suction line.

Inspect; clear.

Sticky or leaking check valve flapper (116).

Clean or replace. See page 16.

Diaphragm ruptured.

Replace. See page 18.

Restricted exhaust.

Remove restriction.

Air bubbles in fluid.

Supply line is loose.

Tighten.

Diaphragm ruptured.

Replace. See page 18.

Loose inlet manifold components, damaged 
gasket (121) between manifold components, 
or damaged check valve gaskets (112, 114).

Tighten manifold bolts (120) or replace 
seats (115) or gaskets (112, 114, or 
121). See page 16.

Loose diaphragm shaft bolt (107).

Tighten or replace. See page 18.

Damaged o-ring (108).

Replace. See page 18.

Fluid in exhaust air.

Diaphragm ruptured.

Replace. See page 18.

Loose diaphragm shaft bolt (107).

Tighten or replace. See page 18.

Damaged o-ring (108).

Replace. See page 18.

Equipment exhausts 
excessive air at stall.

Worn air valve block (7), o-ring (6), plate (8), 
pilot block (18), u-cups (10), or pilot pin o-rings 
(17).

Repair or replace. See page 21.

Worn shaft seals (402).

Replace. See page 18.

Summary of Contents for Aluminum Husky 2150 LP



































Reviews: