background image

Instructions 

2

3A1963G

Instructions

Warnings

Also see the G3 Pump Instruction manual for additional 
warnings.

Pressure Relief Valves 

The pressure relief valve 
uses a pressure adjustment 
screw (a) to set the pres-
sure release point. 

It is not 

intended as a way to 
relieve pressure during 
normal operation

 but as a 

protective measure in the 
event there is an unin-
tended pressure increase in 
the system. 

NOTE:

 

Do not use this pressure relief valve as a means 
of relieving pressure in day-to-day, normal cycle 
operation. Use the pressure relief procedure 
described on page 3 of
 this manual to relieve 
pressure during normal cycle operation.

The pressure relief valve included in this kit can 
only be used with the Graco G3 Pump. It is not 
intended for use with any other products.

Factory set to 4000 psi (275.8 bar, 27.6 MPa).

The pressure adjustment screw (a) will require periodic 
adjustments. Whenever the valve is set/adjusted (after 
the set point is found) it is important to ensure that the 
valve is not bottomed out and there is at least 1/2 turn of 
adjustment remaining. This is determined by turning the 
screw (a) 1/2 turn and then back turning it out again. 

NOTE:

 Turning adjustment screw (a) clockwise, 

increases pressure.

ELECTRIC SHOCK HAZARD

 

This equipment must be grounded

.

 Improper grounding, 

setup, or usage of the system can cause electric shock.

Turn off and disconnect power cord before servicing 
equipment.

Connect only to grounded electrical outlets.

Use only 3-wire extension cords.

Ensure ground prongs are intact on power and 
extension cords.

Do not expose to rain. Store indoors

SKIN INJECTION HAZARD 

High-pressure fluid from dispense device, hose leaks, or 
ruptured components will pierce skin. This may look like 
just a cut, but it is a serious injury that can result in 
amputation. 

Get immediate surgical treatment. 

Follow 

Pressure Relief Procedure

 in this manual, 

when you stop dispensing and before cleaning, check-
ing, or servicing equipment. 

a

locking
nut

Summary of Contents for 571169









Reviews: