background image

       684-001

8

PARTS LIST

MODEL:  952-793
Includes items 1-31

REF

PART

NO.

NO.

DESCRIPTION

QTY

1

207-546 AIR MOTOR

(see 307-043 for parts)

1

2

902-980 CYLINDER, pump

1

3

902-983 ROD, displacement

1

4     *

101-946 PIN, cotter; 1/8 dia; 1” lg

1

5

102-218 CLAMP, hinged; 1-1/2”

1

6

512-913 MUFFLER, air exhaust

1

7

102-657 CLAMP, hinged; 2-1/2”

3

8    **

180-238 PACKING, “V” block

1

9    *

103-462 BALL; 3/4” dia.

1

10  **

604-016 BEARING, 4” dia.

1

11   *

166-114 SHIELD, drip; neoprene

1

12   ** 166-117 GASKET, sanitary

3

13   ** 166-119 PACKING, o-ring; neoprene

1

14   *

166-129 SHIELD, drip; neoprene

1

15   *

166-130 GASKET, 1-1/2” dia; neoprene

1

16

604-017 STOP, foot valve

1

17   ** 180-919 BEARING, sleeve

1

18

605-570 CYLINDER, foot valve

1

19   ** 167-971 SEAL, piston; neoprene

1

20   ** 167-972 PACKING, o-ring; nitrile rubber

1

21

167-974 ROD, connecting

1

22

167-975 HOUSING, retainer

1

23

604-018 POPPET, foot valve

1

24

180-018 HOUSING, packing

1

25

169-845 PIN, retaining; piston housing

1

26

902-982 ROD, connecting

1

27

604-015 PISTON, priming

1

28

604-008 PIN, retaining

1

29   ** 603-778 PACKING, foot valve

2

30   **

501-095   

SPRING

, ball check                        

1

31

172-573 PLATE, instruction

1

*

Suggested “tool box” spare parts.  Keep on 
hand to reduce down time.

**

Included in Repair Kit 948-147

948-147 REPAIR KIT

(Must be purchased separately)

REF

REF.

NO.

QTY

NO.

QTY

8

1

19

1

10

1

20

1

12

3

29

2

13

1

30

1

17

1

HOW TO ORDER REPLACEMENT PARTS

1. To be sure you receive the correct

replacement parts, kit or accessories, always
give all of the information requested in the
chart below.

2.  Check the parts list to identify the correct part

number; do not use the ref. no. when
ordering.

3. Order all parts from your nearest Graco

distributor.

  6 digit
  PART
  NUMBER

QTY

DESCRIPTION

Summary of Contents for 5:1 Monark 952-793













Reviews: