background image

2

307133

Table of Contents

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operation

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts

8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Warranty

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Information

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

D

This equipment is for professional use only.

D

Read all instruction manuals, tags, and labels before operating the equipment.

D

Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.

D

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

D

Check equipment daily. Repair or replace worn or damaged parts immediately.

D

Do not exceed the maximum working pressure of the lowest rated system component. Refer to the
Technical Data on page 9 for the maximum working pressure of this equipment.

D

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data
 section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

D

Do not exceed the maximum working pressure of the lowest rated system component. This equip-
ment has a 50 psi (350 kPa MPa, 3.5 bar) maximum working pressure.

D

Do not kink or over bend hoses or use hoses to pull equipment.

D

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82

_

C (180

_

F) or below –40

_

C (–40

_

F).

D

Wear hearing protection when operating this equipment.

D

Do not lift pressurized equipment.

D

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

D

Never use 1.1.1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in pressurized aluminum equipment. Such use could result in a
chemical reaction, with the possibility of explosion.

Summary of Contents for 307133P











Reviews: