background image

Installation 

12

3A8503C

Installation

Grounding

Transfer Pump Controller: 

Grounded through the 

power cord.

Transfer Pump: 

Grounded through the Transfer Pump 

Controller. Follow 

Connect Electric Motor Cables to 

the TPC

.

The following items are sold separately:

Fluid hoses:

 Use only electrically conductive hoses 

with a maximum of 300 ft (91 m) combined hose length 

to ensure grounding continuity. Check electrical 

resistance of hoses. If total resistance to ground 

exceeds 29 megohms, replace the hose immediately. 

Fluid supply container:

 Follow local code.

Solvent pails used when flushing:

 Follow local code. 

Use only conductive metal pails, placed on a grounded 

surface. Do not place the pail on a non-conductive 

surface, such as paper or cardboard, which interrupts 

grounding continuity.

To maintain grounding continuity when flushing or 

relieving pressure: 

Hold metal part of the spray gun 

firmly to the side of a grounded metal pail, then trigger 

the gun.

Install the Transfer Pump 

Controller (TPC)

Connect Electric Motor Cables to the TPC

NOTE:

 Refer to your Reactor 3 manual for proportioner 

component identification.

1. Loosen captive fasteners and remove TPC cover 

(ZC).

The equipment must be grounded to reduce the risk 

of static sparking. Static sparking can cause fumes 

to ignite or explode. Grounding provides an escape 

wire for the electric current.

Ground Screw

All electrical wiring must be done by a qualified 

electrician and comply with all local codes and 

regulations. 
Switch off power and unplug the TPC. Wait five 

minutes for power to dissipate before servicing.

Summary of Contents for 26D000





































Reviews: