Graco 25U546 Manual Download Page 33

Page: 33 / 48

Troubleshooting

3A9031A

Electrical

Symptom: Sprayer does not run, stops

running, or will not shut off.

1. Perform

Pressure Relief Procedure

page 10.

2. Install fully charged battery, see

Battery

Installation and Removal

, page 14.

3. Turn the ON/OFF switch

OFF,

wait 30

seconds and then turn power back

again (this ensures sprayer is in normal

run mode).

4. Turn pressure control knob clockwise

1/2 turn.

Problem

What to Check

How to check

Sprayer does not run at all.

Check battery charge.

Press charge level indicator on

battery. Charge battery or

install a new battery, if

needed.

Check pressure control

connections.

Make certain connector is

clean and firmly connected.

Check pressure control.

Connect known good pressure

control. If the motor runs,

replace pressure control.

Check motor leads.

Make certain terminals are

clean and firmly connected.

Check all wiring harnesses for

pinched or severed wires

(power switch, motor,

pressure control).

Repair wires or bring to Graco

certified repair shop.

Sprayer will not shut off after

reaching or exceeding

maximum pressure.

Check pressure control.

Disconnect pressure control, if

sprayer still runs, replace

control board. If the sprayer

stops, replace pressure

control.

Basic electrical problems

Motor leads are securely

fastened and properly mated

Replace loose terminals; crimp

to leads. Be sure terminal are

firmly connected.
Clean circuit board terminals.

Securely reconnect leads.

Summary of Contents for 25U546

















































Search results

Summary of Contents for 25U546

Reviews:

Related manuals for 25U546

Brands by name

Popular brands

Graco 25U546, Manual

Search results

Summary of Contents for 25U546

Reviews:

Related manuals for 25U546

Brands by name

Popular brands