background image

Maintenance 

16

3A7519A

13. Replace the o-rings (28) on the seal retainer (6) 

using the parts from the seal repair kit (F

IG

. 29).

14. Replace the seal retainer (6) and hand-tighten (F

IG

30).

15. Apply anti-seize lubricant to the male threads of the 

pulp cylinder (2) then reinstall the assembly. Tighten 
using a 1-13/16 in. socket (torque 235 - 265 
ft-lb/318.6 - 359.3 N•m).

16. Using a 1-7/16 in. socket, tighten the seal retainer 

(6) to the pump cylinder (2) assembly (torque 100 - 
110 ft-lb/135.6 - 149.1 N•m) (F

IG

. 31).

17. Reinstall the inlet pump tube assembly, connect the 

shovel rod (20), located inside of the inlet pump tube 
(8), and attach to the connecting rod (13) using a 
3/4 in. socket and tighten (torque 55 - 65 ft-lb/ 74.6 - 
88.1 N•m) (F

IG

. 32).

NOTE: The shovel rod (20) should remain inside of the 
inlet pump cylinder (8).

18. Reinstall the inlet cylinder (8) and tighten using a 

1-15/16 in. socket (torque 75 - 85 ft-lb/101.7 - 115.2 
N•m) (F

IG

. 33).

NOTE: Remove any grease on the internal threads of 
the inlet cylinder before reinstalling to ensure correct 
threading.

F

IG

. 29

F

IG

. 30

30

29

6

2

28

F

IG

. 31

F

IG

. 32

20

8

13

Summary of Contents for 25P784





























Reviews: