background image

Setup

3A5202G

7

Setup

Assemble Unit

If unit is already assembled, continue to 

Prepare Unit 

for Operation

.

1. Unfold cart legs and stand cart upright.

2. Install frame safety pins (BA) at front and rear of 

cart. 

3. Using a two-person lift, place the hopper (A) on top 

of the cart frame. Secure the hopper to both sides of 
cart using the hopper ring pins (G).

4. Fully insert the material dosing auger shaft (FD) into 

the rear end of the hopper (A). 

5. Insert mix shaft (FB) into mix tube (FA). Install shaft 

and tube onto hopper (A).
a. Align mixing shaft pins (FBB) to slots in the 

material dosing auger shaft (FD) and verify that 
pins and shaft are fully engaged.

b. Firmly connect mixing tube (FA) to hopper (A). 

Secure mixing tube toggle latches (FAA).

6. Lift the motor assembly (C) so that it connects to the 

material dosing auger shaft (FD). Immediately 
secure the motor to the hopper with the motor 
alignment pin (CA). Ensure the pin has slid 
completely into place. Slide motor alignment pin 
washer (CAB) over the end of the alignment pin 
(CA). Secure alignment pin with motor alignment pin 
clip (CAA).

7. Engage the rear toggle latch (BB) on the rear cart 

leg. Secure with rear toggle latch clip (BBA).

8. Connect motor power cable (CB).

During assembly, the cart could collapse and crush 
fingers and other body parts. To avoid possible injury, 
make sure all clips and pins are securely in place and 
the mixer is on level ground.

Be sure to properly support the mixer with a 
two-person lift during transport. Do not suspend from 
crane or hoist. The mixer is heavy and can crush 
fingers and other body parts.

WLD

&$

&$$

&

&

&$%

WLD

%%

%%$

&

&%

WLD

Summary of Contents for 25M081

































Reviews: