background image

Technical Data

308687L

13

Technical Data 

IM5 Inline Electronic Meter

US

Metric

Flow range

0.5 to 5 gpm

1.9 to 19 lpm

Maximum working pressure

500 psi

3.4 MPa, 34 bar

Minimum working pressure

5 psi

34 kPa, 0.3 bar

Weight

Weight

1.8 lbs

0.82 kg

Units of Measurement

Factory-setting

quarts

Accuracy

+/- 0.5 percent

Measured at 2.5 gpm (9.5 lpm), at 70°F (21°C), with 10-weight oil and 1 gallon dispensed. May require 
calibration; out-of-box accuracy is +/- 1.25 percent.
Repeatability

+/- 0.15 percent

Measured at 2.5 gpm (9.5 lpm), at 70°F (21°C), with 10-weight oil and 1 gallon dispensed. 

Inlet / Outlet: Meter can be installed with flow 
in either direction

1/2 npt

Temperature

Operating temperature range

-4°F to 122°F

-20°C to 50°C

Storage temperature range

-13°F to 122°F

-25°C to 50°C

Materials of Construction

Wetted parts

nickel, zinc, LCP, nitrile rubber

Battery Information

Battery

standard 9V alkaline: Duracell

®

 MN1604, Duracell PC1604, 

Eveready

®

 EN22, Eveready 522

Duracell® is a registered trademark of Duracell Inc.

Eveready® is a registered trademark of the Eveready Battery Co., Inc.

Summary of Contents for 239824















Reviews: