manualshive.com logo in svg

Grace GMQ Pro, Manual

Share
Download
Grace GMQ Pro Manual Download Page 26

26

(ID: 040708)

1/4" X 2-1/4" 

Carriage Bolt

Carriage Stop Base

3/16" Flat Washer

1/4" Jam Nut

Carriage Stop Clamp

1-1/4" Fender Washer

1/4" Plastic Knob

Step 25:  Carriage Stop Assembly

Parts Needed:  2- Carriage Stop Base

 

 

2- Carriage Stop Clamp

 

 

2- M6 x 55mm Carriage Bolt

 

 

2- M5 Flat Washer

 

 

2- M6 Jam Nut

 

 

2- M8 Fender Washer

 

 

2- M6 Plastic Knob

• You will be building two 

carriage stops, but one at a time.

•  At the end of  the carriage bolt you will need to put a flat washer followed by a jamb nut.  

•  TIGHTeN  the jam nut completely on the bolt, and make 

sure the top of  the bolt is flush against the wood.

•  Once you have the jam nut on the bolt you will then slide 

the Carriage Stop Clamp on the bolt.  

•  On the end of  the bolt you will put a fender washer and a 

plastic knob.  Before you tighten the knob you will want to 

decide where you want your stop,  as shown above, then you 

will tighten the knob so it will stay on your frame.

•  You will follow the above steps to complete the other 

carriage stop.

• You will be building two carriage stops, but one at 

a time.

•  Take the carriage bolt and place it through the 

Carriage Stop Base.

M8 Fender Washer

M6 x 55mm      

Carriage Bolt

M6 Jam Nut

M5 Flat 

Washer

M6 Plastic Knob

Summary of Contents for GMQ Pro
































Reviews:

No comments

Brands by name

Popular brands

Load more brands