manualshive.com logo in svg

Grace GMQ Pro, Manual, Page: 15 / 31

Share
Download
Grace GMQ Pro Manual Download Page 15

15

(ID: 040708)

1/4" X 1" Phillips

Pan Head Screw

1/4" X 1" Phillips

Pan Head Screw

1/4" X 3/4" Phillips

Pan Head Screw

1-1/4" Fender Washer

1/4" Plastic Knob

1/4" Flat Washer

1/4" Nylock Nut

1/4" X 3/4" Phillips

Head Pan Screw

1/4" Plastic Knob

1-1/4" Fender Washer

1/4" Flat Washer

1/4" Nylock Nut

6MM Plastic 

Knob

6MM Plastic 

Knob

Step 9: Frame End Assembly to Table Assembly

Parts Needed:  1- Table Assembled (Crib or Queen or King)

 

 

1- Right and Left Frame end Assembly

 

 

8- M6 X 25mm Phillips Pan Head Screw

•  Attach the Left Frame end to Table 

#1, as pictured below, with the bolts 

facing  away from the frame.

•  Tip your table so it is upside down, if  it is not that way 

already.

Step 10: Side Leg to Table Assembly

Parts Needed:  1- Table Assembly (Crib or Queen or King)

 

 

2- Right and Left Back Leg (assembled)

 

 

2- Right and Left Front Leg (assembled)

 

 

4- M6 x 20mm Phillips Pan Head Screw

 

 

4- M6 Flat Washer

 

 

4-M6 Nylock Nut

 

 

4- M8 Fender Washer

 

 

4- 6MM Plastic Knob

•  Put a screw through each hole on the outside corners of  the Left 

Frame end, and into the holes in the track supports.  

•   You will attach the Right Frame end to the right side of  your table. 

(#2 if Crib, #3 if  Queen, and #4 if King)

•  The bolt closest to the floor is where you will place a fender washer 

followed by a plastic  knob.

•  Then you will take a screw and insert it through the front track support 

to the Outer Leg Brace B, where it will screw into a pre installed nut.

•  Take your Front Left Leg and 

place it on the bolts that stick 

out of  your Left Frame end, (as 

pictured left).

•  Place a flat washer followed by a nylock nut on 

the bolt above the plastic knob.

**NOTe!!  Leave all the nylock nuts loose enough 

to slide in the joint, and loose enough to allow the 

washer to turn in your fingers!**

•  Follow the above instructions to install the Left 

Back Leg as well as the Right Front and Back Legs.

M6 x 25mm Philips Pan 

Head Screw

M6 x 25mm Philips 

Pan Head 

Screw

M6 x 20mm Philips Pan 

Head Screw

M8 Fender Washer

M6 Flat Washer

M6 Nylock Nut

M6 x 20mm Philips Pan 

Head Screw

M8 Fender Washer

M6 Nylock Nut

M6 Flat Washer

Summary of Contents for GMQ Pro
































Reviews:

No comments