manualshive.com logo in svg

Gorilla Playsets Pioneer Peak 1500DW, Manual

Share
Download
Gorilla Playsets Pioneer Peak 1500DW Manual Download Page 76

STEP 18C: CLIMBING RAMP

1: LOCATE FOUR 2 X 4 X 18" RAMP POST SUPPORTS.
2: PLACE A RAMP POST SUPPORT AGAINST THE RAMP POST AND THE RAMP SIDE AS SHOWN 

BELOW.
3: THE BOTTOM OF THE RAMP POST SUPPORT SHOULD BE FLUSH TO THE BOTTOM OF THE RAMP 

SIDE.  THE TOP-END OF THE RAMP POST SUPPORT SHOULD BE FLUSH TO THE SIDE OF THE RAMP 

POST.
4: ATTACH THE TOP OF THE RAMP POST SUPPORT TO THE RAMP POST WITH ONE #8 X 2-1/2" 

WOOD SCREW AND ONE #8 X 3-1/2" WOOD SCREW.
5: ATTACH THE BOTTOM OF THE RAMP POST SUPPORT TO THE RAMP SIDE WITH FOUR #8 X 2-1/2" 

WOOD SCREWS.
6: REPEAT SUBSTEPS 2 TO 5 FOR THE REMAINING RAMP POST SUPPORTS.

RAMP POST

RAMP SIDE

RAMP POST

SUPPORT

SUPPORT

RAMP POST

SUPPORT

RAMP POST

SUPPORT

RAMP POST

RAMP POST

A

#8 X 2-1/2"

WOOD SCREW

#8 X 2-1/2"

WOOD SCREW

RAMP POST

SCALE 2 : 13

DETAIL A 

SUPPORT

RAMP POST

WOOD SCREW

2 x 4 x 18"

#8 X 3-1/2"

RAMP SIDE

66

Summary of Contents for Pioneer Peak 1500DW





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands