manualshive.com logo in svg

Gorilla Playsets Pioneer Peak 1500DW, Manual

Share
Download
Gorilla Playsets Pioneer Peak 1500DW Manual Download Page 139

2 X 4 X 27"

SUPPORT

ROOF SUPPORT - LEFT

ROOF SUPPORT - RIGHT

SUPPORT ASSEMBLY

(MAKE 2)

COUNTERSUNK HOLE FACES DOWN

2 X 4 X 27" 

5/4 X 6 X 10"

ROOF PEAK 

COMPLETED ROOF 

A

DETAIL A 

SCALE 1 : 3

FLUSH

#8 X 2"

WOOD SCREW

FLUSH

1: LOCATE FOUR 2 X 4 X 51-1/8" ROOF SUPPORT (LEFT), FOUR 2 X 4 X 51-1/8" ROOF SUPPORT (RIGHT) AND FOUR 5/4 

X 6 X 10" ROOF PEAK SUPPORT PIECES.

2: FIND A FLAT SURFACE TO WORK ON. LAY THE ROOF SUPPORTS DOWN ON THE FLAT SURFACE WITH THE 

COUNTERSUNK HOLES FACING DOWN. ALIGN THE ANGLED ENDS OF THE ROOF SUPPORTS FLUSH WITH ONE 

ANOTHER. PLACE A ROOF PEAK SUPPORT ON TOP OF THE ROOF SUPPORTS AS SHOWN. THE EDGES SHOULD BE 

FLUSH WHERE SHOWN BELOW.

3: USE FOUR #8 X 2" WOOD SCREWS TO ATTACH THE ROOF PEAK SUPPORT TO THE ROOF SUPPORTS AS SHOWN 

BELOW.

4: MAKE ONE MORE ROOF SUPPORT ASSEMBLY BY REPEATING 2 AND 3.

STEP 22: ROOF SUPPORT ASSEMBLIES

FLUSH

129

Summary of Contents for Pioneer Peak 1500DW





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands