manualshive.com logo in svg

Gorilla Playsets Hemisphere 2500W, Assembly Instructions Manual, Page: 71 / 88

Share
Download
Gorilla Playsets Hemisphere 2500W Assembly Instructions Manual Download Page 71

1: PLACE A ROOF SUPPORT ASSEMBLY ON TOP OF THE FRONT ROOF SUPPORT.  THE ROOF 

SUPPORT ASSEMBLY SHOULD HAVE THE ROOF PEAK SUPPORTS FACING OUT.

2: CENTER THE ROOF SUPPORT ASSEMBLY WITH THE FRONT ROOF SUPPORT. FROM THE 

INSIDE DRIVE FOUR #8 X 2-1/2" WOOD SCREWS THROUGH THE FRONT CENTER POST INTO 

THE BACK SIDE OF THE ROOF SUPPORTS.  NOW DRIVE A #8 X 3" WOOD SCREW AND A #8 

X 2" WOOD SCREW INTO THE END OF EACH ROOF SUPPORT.

STEP 35: MOUNTING THE FRONT ROOF SUPPORT ASSEMBLY

THIRD:

ASSEMBLY

ROOF SUPPORT

FRONT

ROOF PEAK SUPPORTS FACE OUT

CENTER ROOF SUPPORT ASSEMBLY

ON TOP OF  FRONT ROOF SUPPORT

ROOF SUPPORT

FIRST:

FRONT SIDE OF FORT WITH WINDOWS 

FACING OUT

THIRD:

#8 X 2" 

WOOD SCREW

(1)

#8 X 2" 

WOOD SCREW

(1)

#8 X 3" 

WOOD SCREW

(1)

INSIDE OF FRONT FACE OF  FORT

SECOND:

#8 X 2-1/2" 

WOOD SCREWS

(4)

#8 X 3" 

WOOD SCREW

(1)

63

Summary of Contents for Hemisphere 2500W

























































































Reviews:

No comments