manualshive.com logo in svg

Gorilla Playsets Hemisphere 2500W, Assembly Instructions Manual, Page: 70 / 88

Share
Download
Gorilla Playsets Hemisphere 2500W Assembly Instructions Manual Download Page 70

THE ROOF SUPPORTS.  NOW DRIVE A 2" AND A 3" WOOD SCREW INTO THE PREDRILLED 

STEP 34: ROOF SUPPORTS

2: REPEAT SUBSTEP 1 TO COMPLETE A SECOND ROOF SUPPORT ASSEMBLY.

HOLES TO SECURE THE ROOF SUPPORTS TOGETHER. 

1: PLACE TWO 2 X 6 X 34-3/16" ROOF SUPPORTS ON A FLAT SURFACE.  ALIGN THE TIPS OF 

3: PLACE TWO OF THE 5/4 X 6 X 8-7/16" ROOF PEAK SUPPORTS ON TOP OF THE ROOF 

SUPPORTS AS SHOWN BELOW.  THE TIPS OF THE ROOF PEAK SUPPORTS SHOULD BE ALIGNED 

WITH THE TIPS OF THE ROOF SUPPORTS.  ALSO THE SIDES OF THE ROOF PEAK SUPPORTS 

SHOULD BE FLUSH TO THE SIDES OF THE ROOF SUPPORTS. SECURE EACH ROOF PEAK SUPPORT 

TO THE ROOF SUPPORT WITH TWO #8 X 2" WOOD SCREWS.

4: NOW DRIVE A #8 X 3" WOOD SCREW THROUGH THE SIDE OF THE ROOF PEAK SUPPORT 

INTO THE OTHER ROOF PEAK SUPPORT.

5: REPEAT SUBSTEPS 3 AND 4 TO COMPLETE THE SECOND ROOF SUPPORT ASSEMBLY.

#8 X 2" WOOD SCREW

#8 X 3" WOOD SCREW

2 X 6 X 34-3/16"

ROOF SUPPORT

2 X 6 X 34-3/16"

ROOF SUPPORT

ROOF SUPPORT ASSEMBLY

#8 X 3"

WOOD 

SCREW

ROOF PEAK SUPPORT

(2) PER SIDE

#8 X 2" WOOD SCREW 

FLUSH

5/4 X 6 X 8-7/16"

#8 X 3" 

WOOD 

SCREW

62

Summary of Contents for Hemisphere 2500W

























































































Reviews:

No comments