Gorilla Playsets 1500GWF Manual Download Page 75

Page: 75 / 177

THROUGH THE BACK SIDE OF THE ROPE LADDER SUPPORT.

KNOT SHOULD BE 6" BELOW THE ROPE LADDER SUPPORT.

6) REPEAT 4 & 5 FOR REMAINING ROPE LADDER RUNGS.

5) SLIDE THE NEXT ROPE LADDER RUNG UP TO THE

MARKS OR TAPE. TIE THREE KNOTS UNDER THE ROPE

ROPE LADDER SUPPORT

2) MEASURE DOWN 6" BELOW THE BOTTOM OF THE ROPE

3) TIE THESE THREE KNOTS BELOW THE ROPE LADDER RUNG.

LADDER RUNG.

1) TIE A KNOT IN EACH ROPE AND THREAD THEM

ROPE LADDER RUNNER

LADDER SUPPORT AND TIE 3 KNOTS. THE BOTTOM OF EACH

THIS IS THE VIEW AS IF YOU WERE STANDING AT THE FRONT - LEFT OF THE PLAY SET

THE ROPE OR MARK WITH A PEN.

4) MEASURE DOWN 10-5/8" BELOW THE

ROPE LADDER RUNG AND PLACE TAPE ON

7) TIE KNOTS ON BACK SIDE OF ROPE LADDER RUNNER.

2.1) SLIDE A ROPE LADDER RUNG AGAINST THE THREE KNOTS.

10 58 "

STEP 20: ROPE LADDER

1: FIND THREE ROPE LADDER ROPES. MAKE A KNOT IN THE END OF EACH ROPE AND THREAD THE FREE END THROUGH

THE BACK SIDE OF THE ROPE LADDER SUPPORT. PULL EACH ROPE TAUGHT.

2: MEASURE DOWN FROM THE BOTTOM OF THE ROPE LADDER SUPPORT 6 INCHES AND TIE A KNOT. THE BOTTOM OF THE

KNOT SHOULD BE 6 INCHES BELOW THE ROPE LADDER SUPPORT. SLIDE EACH ROPE THROUGH THE HOLES IN ONE ROPE

LADDER RUNG. SLIDE THE RUNG UP AGAINST THE BOTTOM OF THE KNOTS.

3: TIE THREE KNOTS BELOW THE ROPE LADDER RUNG.

4: MEASURE DOWN FROM THE BOTTOM OF THE ROPE LADDER RUNG 10-5/8 INCHES AND MAKE A MARK ON THE ROPE

WITH A PIECE OF TAPE OR A MARKER. THREAD ANOTHER ROPE LADDER RUNG ONTO THE ROPES.

5: WITH THE TOP OF THE RUNG EVEN WITH THE 10-5/8" MARK TIE THREE KNOTS BELOW THE SECOND ROPE LADDER

RUNG.

6: REPEAT SUBSTEPS 4-5 FOR THE REMAINING ROPE LADDER RUNGS.

7: THREAD THE BOTTOM END OF EACH ROPE THROUGH THE HOLES IN THE ROPE LADDER RUNNER AND TIE THEM OFF.

GRAB EACH ROPE AND ATTEMPT TO WRAP IT AROUND YOUR HAND. IF THE ROPE WRAPS AROUND YOUR HAND IT IS TOO

LOOSE. IF THE ROPE IS TOO LOOSE UNTIE THE KNOT BEHIND THE ROPE LADDER RUNNER AND RETIE IT UNTIL YOU CAN

NO LONGER WRAP THE ROPE AROUND YOUR HAND.

Summary of Contents for 1500GWF


















































































































































































Search results

Summary of Contents for 1500GWF

Reviews:

Related manuals for 1500GWF

Brands by name

Popular brands

Gorilla Playsets 1500GWF, Manual

Search results

Summary of Contents for 1500GWF

Reviews:

Related manuals for 1500GWF

Brands by name

Popular brands