background image

Instructions for use, mounting and connection

41

 Important warnings

• 

The appliance may be built-in and connected to
the power supply only by a qualified technician.

• 

Particular areas of the cooktop surface
(adjacent to the hotplates) are hot during
operation. Prevent the children to hang around
the appliance and warn them properly against
the danger of burns.

• 

Hot oil ignites readily, so be sure have the
preparation of such food (fries) under constant
control.

• 

Hotplates may not be left in operation empty,
without any dishes on top.

• 

Never use the appliance for heating the
ambience.

• 

Never use the ceramic-glass cooktop as a
working surface. Sharp objects may damage
the cooktop surface.

• 

Preparation of food in aluminum or plastic
cookware is not allowed. Never place any
plastic objects or aluminum foil upon the
cooktop surface.

• 

In case any other appliances are plugged in the
electric mains close to the cooktop, prevent the
contact of the plug cable with the hot cooking
zones.

• 

Never keep any flammable or temperature
sensitive objects, like cleaning agents, sprays,
detergents, etc., below the appliance.

• 

Never use cracked or broken ceramic-glass
cooktop. In case you notice any visible cracks
on the surface, cut the power supply
immediately.

• 

In case of any malfunctions, disconnect the
appliance from the power supply and call
service department.

• 

Do not use high-pressure steam cleaner or hot
steam to clean the appliance.

• 

The appliance is manufactured in compliance
with the relevant effective safety standards.
Nevertheless, we strongly recommend that
persons with impaired physical, motoric, or
mental capacity, or persons with inadequate
experience or knowledge, do not use the
appliance unless attended by a qualified
person. The same recommendation applies
when the appliance is used by persons of less-
than-legal age.

The symbol on the product or on its
packaging indicates that this product
may not be treated as household waste.

Instead it shall be handed over to the
applicable collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise be
caused by inappropriate waste handling of
thisproduct. For more detailed information
about recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where you
purchased the product.

Connection to the power supply

• 

Connections may be carried out by a qualified
technician only. The earthing protection must
comply with the standing regulations.

• 

Connection terminals are revealed when the
connection box cover is removed.

• 

Prior any attempted connection check that the
voltage indicated on the rating plate is in line with
your home power supply.

• 

The rating plate is located underneath the
appliance.

• 

The appliance is manufactured for use with the
power supply voltage AC 230 V.

• 

The electric wiring should be equipped with a
circuit breaker able to isolate the appliance from
the mains in all points, with the distance between
terminals of at least 3 mm in open position. This
may be done by means of fuses, safety switches,
etc.

• 

The connection should be selected in accordance
with the declared charge capacity of the mains
and the fuse power.

• 

Such appliances are allowed to be mounted on
one side next to a high kitchen cabinet, the height
of which may exceed that of the appliance. On the
opposite side however, only a kitchen cabinet of
equal height as the appliance is allowed.

• 

Upon the completion of installation, live wires and
isolated cables must be adequately protected
against accidental touching.

• 

Distance between the cooktop surface and the
cooking hood must be such as indicated in the
instructions for use of the hood.

• 

Kitchen cabinets may not be mounted underneath
the built-in ceramic-glass cooktop.

Summary of Contents for SVK61TS



















Reviews: