background image

Instructions for use, mounting and connection

43

• 

The smallest distance between the edge of the
appliance and  the adjacent high kitchen cabinet is
40 mm.

• 

The use of hard wood decorative borders around
the worktop behind the appliance is allowed, in
case the minimum distance remains as indicated
on the installation illustrations.

• 

Minimum distance between the built-in cooktop
and rear wall is indicated at the illustration for the
installation of the built-in cooktop.

• 

The appliance may be installed in any worktop
with a thickness from 30 mm to 50 mm.

Dimensions of the built-in hob opening

Installation procedure

• 

Worktop must be placed absolutely horizontal.

• 

Suitably protect the edges of the cut aperture.

• 

By means of the supplied screws 4 (or 6 by
some models) fasten the supplied tightening
brackets 4 (or 6 by some models) fasten to the
front and the rear side of the cooking hob and
to the prepared aperture.

• 

Connect the cooking hob to the mains power
supply (see instructions for the connection of
the cooking hob to mains power supply).

• 

Insert the hob into the cut aperture.

• 

Press the hob firmly towards the worktop from
above.

Ceramic-glass cooktop

Ceramic-glass cooktop is equipped with four hotplates
designed as cooking zones. The surface of the hob is
flat, without any edges for eventual gathering of dirt.
Cookware may easily be moved about along the hob
surface.

• 

Hotplates quickly reach the selected heating power
while the adjacent area around the hotplates
remains cool.

• 

The cooktop is resistant to temperature changes.

• 

The cooktop is also impact resistant. Cookware
may be placed upon the surface rather firmly
without any consequences.

• 

Avoid using the hob as a working surface. Sharp
objects may produce scratches.

• 

Never attempt to prepare food in aluminum or
plastic cookware. Never place any plastic objects or
aluminum foil upon the hot cooking hob.

• 

Avoid making coffee in traditional Turkish coffee
kettle since the diameter of the bottom is too small
and the hotplate may be damaged.

CAUTION !

• 

Never use cracked or broken ceramic-glass
cooking hob. Sharp edged objects, falling upon the
surface of the hob may cause cracking. The
consequences may be visible immediately or only
after a while. In case any visible cracks are
observed cut the power supply immediately.

• 

In case sugar or other heavily sweetened substance
is spilled on the hotplate, wipe it immediately and
remove the sugar residues with a scraper although
the cooking zone is still hot, otherwise the hotplate
may be damaged.

• 

Avoid cleaning the cooktop while the cooking zones
are still hot, as you may damage the hob.

Summary of Contents for SVK61TS



















Reviews: