background image

1 of 1 

T: 888-593-9988 

|

 F: 713-316-5541 

Produced by Goodman Business Unit Technical Services 

|

 19001 Kermier Road 

|

 Waller, TX 77484 

All rights reserved. Goodman products are subject to continuous improvements. Goodman reserves the right to modify 

information in the bulletin without notice and without incurring any obligations. Amana

®

 is a registered trademark of Maytag 

Corporation or its related companies and is used under license. All rights reserved. 

DATE: October 7, 2020

 

TO: All Service and Parts Managers 

SUBJECT: Crank Case Heater Kit for Inverter Split Systems 

 For reliability and longevity, inverter condensing units are designed to maintain compressor oil 

at optimum conditions while the unit is in stand-by mode. This feature allows a small current 
draw through the compressor windings to maintain proper oil temperature to provide 
compressor protection in preparation for the next run cycle. 

In some cases, homeowners may hear a high-pitched sound coming from the outdoor unit. This 
is the result of current draw through the compressor windings and is not a defect with the 
inverter unit.  If you have a homeowner experiencing this condition and finds it objectionable, we 
have developed a kit to install an external crankcase heater to maintain proper oil temperature 
instead of utilizing the compressor windings on the inverter units. 

This kit is not under the manufacturer’s warranty and must be purchased by contacting your 
service parts CSR.  The part number for the kit is 

INVCCH

K

01

Note:

 Please review 

IO-7005

 (attached) before proceeding with the installation. The “New” 

INVCCH

K

01

 requires the use of the 

BTSDL01

 (Bluetooth Shared Data Loader) in addition to 

this kit to install the required shared data. 

Applicable Models 

AVZC180241 

AVZC200241 

AVXC2000241 

GVZC200241 

GVXC200241 

AVZC180361 

AVZC200361 

AVXC2000361 

GVZC200361 

GVXC200361 

AVZC180481 

AVZC200481 

AVXC2000481 

GVZC200481 

GVXC200481 

AVZC180601 

AVZC200601 

AVXC2000601 

GVZC200601 

GVXC200601 

If you have questions regarding this bulletin, please contact 

[email protected] 

SR – 068 Rev 1

Summary of Contents for AVXC2000241

















Reviews: