background image

21

   Locate the Reed Switch (33) and the Magnet (32) 

on the right side of the Pulley (31). Turn the Pulley 

until the Magnet is aligned with the Reed Switch. 

Make sure that the gap between the Magnet 

and the Reed Switch is about 1/8 in. (3 mm). 

If necessary, loosen the #8 x 3/4" Truss Head 

Screw (14), move the Reed Switch slightly, and 

then retighten the Screw. Carefully slide the Motor 

Hood (not shown) back on by lining up the guides. 

Reattach the Motor Hood with the five #8 x 3/4" 

Screws (not shown) and run the treadmill for a few 

minutes to check for a correct speed reading.

SYMPTOM: The incline of the treadmill does not 

change correctly

a.     Hold down the Stop button and the Speed increase 

button, insert the key into the console, and then 

release the Stop button and the Speed increase 

button. Press the Stop button and then press the 

Incline increase or decrease button. The treadmill 

will automatically rise to the maximum incline level 

and then return to the minimum level. This will re-

calibrate the incline system. If the incline does not 

begin calibrating, press the Stop button again, and 

then press the Incline increase or decrease button 

again. When the incline is calibrated, remove the 

key from the console.

SYMPTOM: The walking belt slows when walked on

a.  

  Use only a single-outlet surge suppressor that 

meets all of the specifications described on page 

13.

b.   If the walking belt is overtightened, treadmill per-

formance may decrease and the walking belt may 

become damaged. Remove the key and UNPLUG 

THE POWER CORD. Using the hex key, turn both 

idler roller screws counterclockwise, 1/4 of a turn. 

When the walking belt is properly tightened, you 

should be able to lift each edge of the walking belt 

2 to 3 in. (5 to 7 cm) off the walking platform. Be 

careful to keep the walking belt centered. Then, 

plug in the power cord, insert the key, and run the 

treadmill for a few minutes. Repeat until the walk-

ing belt is properly tightened.

c.  

Your treadmill features a walking belt coated with 

high-performance lubricant. IMPORTANT: Never 

apply silicone spray or other substances to the 

walking belt or the walking platform unless in-

structed to do so by an authorized service rep-

resentative. Such substances may deteriorate 

the walking belt and cause excessive wear. If 

you suspect that the walking belt needs more lubri-

cant, see the front cover of this manual.

d.   If the walking belt still slows when walked on, see 

the front cover of this manual.

2–3 in.

b

Front

View

33

31

32

1/8 in.

14

Idler Roller Screws

Summary of Contents for Stride Trainer 410





























Reviews: