background image

Problem

 

Possible Cause

 

Prevention/Solution

 

Burner(s) will not 
light using ignition.

 

Wire and/or electrode covered 
with 

 

cooking residue. 

 

Electrode cracked or broken 

 

"sparks at crack”.

 

 

Electrode tip not in proper 
position.

 

 

Wires are loose or disconnected.

 

 

Wires are shorting (sparking) 
between ignition and electrode.

 

 

Dead battery.

 

Clean wire and/or electrode with rubbing 

 

alcohol and clean swab.

 

Replace electrode(s).

 

Reconnect wires or replace electrode/wire 

 

assembly.

 

Replace ignition wire/electrode assembly.

 

Replace with a new AA battery.

 

Burner(s) will not

 

Light using match 
stick.

 

No gas flow. 

 

Coupling nut and regulator not 
fully connected. 

 

Obstruction of gas flow. 

 

Disengagement of burner to valve. 
Is grill assembled correctly? 

Check to see if LPG tank is empty. If LPG 
tank is not empty, refer to 

"Sudden drop in 

gas flow".

 

Turn the coupling nut until solid stop.  
Clear burner tube(s).

 

Reengage burner and valve.

 

Check steps in assembly instructions.

 

Sudden drop in 
gas flow or low 
flame.

 

Out of gas. 

 

Excess flow valve tripped.

 

Check for gas in LPG tank.

 

Turn off knobs, wait 30 seconds and light grill. 
If 

 

flames are still low, turn off knobs and LPG 

tank valve. Disconnect regulator. Reconnect

 

regulator and leak test 

(Procedure located 

on Page 2 of this manual)

. Turn on LPG 

tank valve, wait 30 seconds and then light 
grill.

 

Flames blow out.

 

High or gusting winds. 

 

Low on LPG gas.

 

 

Excess flow valve tripped.

 

Turn front of grill to face wind or increase 
flame height.

 

Refill LPG tank.

 

Refer to 

"Sudden drop in gas flow" 

above.

 

Flare-up.

 

Grease buildup. 

 

Excessive fat in meat.

 

 

Excessive cooking temperature.

 

Clean grill.

 

Trim fat from meat before grilling.

 

Adjust (lower) temperature accordingly.

 

Persistent grease 
fire.

 

Grease trapped by food buildup 
around burner system.

 

Turn knobs to OFF. Turn gas off at LPG tank. 
Leave lid in position and let fire burn out.

 

After grill cools, remove and clean all parts.

 

Flashback

 

(fire in burner 
tube(s).

 

Burner and/or burner tubes are 

 

blocked.

 

Turn knobs to OFF. Clean burner and/or 

 

burner tubes.

 

Troubleshooting 

Page 24 

Summary of Contents for Kiwi Choice GBQKC140





























Reviews: