background image

 

Safety Cautions 

Danger

: Please use correct AC power voltage source shown on 

the sticker attached on the equipment to avoid any damage. 
Please do not open the case. High voltages exist and are 

accessible. Use extreme caution when servicing internal components. 
For maintenance, please contact the manufacturer or distributor directly. 

Danger

: Turn drive off before removing or installing tubing. Fingers or 

loose clothing could get caught in drive mechanism. 
 

Warning

: Tubing breakage may result in fluid being sprayed 

from pump. Use appropriate measures to protect operator and 

equipment. 

Warning

: Remove power from pump before attempting any maintenance 

or any cleaning operation is started. 

Warning

: Remove power from pump before connecting or disconnecting 

the external control device or communication interface. 

Warning

:  Pump is provided with a grounded plug, it must be well 

grounded at all times. 

Warning

: This product is not designed for, nor intended for use in patient 

connected applications; including, but not limited to, medical and dental 
use. 

 
 

 

 

Summary of Contents for BT103S



























Reviews: