manualshive.com logo in svg

Goblin 380 KYLE STACY EDITION, User Manual

Share
Download
Goblin 380 KYLE STACY EDITION User Manual Download Page 37

Uniball M2 Male

(H0538-S)

- 5 x Uniball M2 Male.

- 1 x Battery Block.

- 1 x Button Cap Screws M2x5.

Canopy Nut

(H0542-S)

- 2 x Canopy Nut.

- 2 x Set Screws M4x20mm.

Canopy Knob

(H0543-S)

- 2 x Canopy Knob.

Yellow/Blue Canopy

(H0544-S)

Red/Black Canopy

(H0545-S)

Yellow Boom

(H0546-S)

Red Boom

(H0547-S)

Plastic Servo Support

(H0548-S)

- 1 x Plastic Servo Support.

- 1 x Head Cap Screws Shoudered

        M2.5x18mm.

Tail Blade 70

(H0554-S)

- 2 x Plastic Servo Support.

Linkage Rod M2

(H0561-S)

- 2 x Linkage Rod M2x22mm.

- 4 x Plastic Ball Link M2.

FBL Support

(H0564-S)

- 1 x FBL Support.

- 2 x Head Cap Screw M2.5x8.

Tail Damper

(H0567-S)

- 2 x Tail Damper.

- 1 x Yellow/Blue Canopy.

- 1 x Canopy Edge Protection.

- 2 x Canopy Grommet.

- 1 x Red/Black Canopy.

- 1 x Canopy Edge Protection.

- 2 x Canopy Grommet.

- 1 x Yellow Tail Boom.

- 1 x M8 Carbon Block.

- 2 x Locking Element Tail.

- 1 x Double Sided Tape [HA034].

- 1 x Double Sided Tape [HA033].

- 1 x Metrix Hex Nylon Nut M8.

- 1 x Metrix Hex Nylon Screw M8.

- 4 x Metrix Hex Nylon Nut M2.5.

- 1 x Red Tail Boom.

- 1 x M8 Carbon Block.

- 2 x Locking Element Tail.

- 1 x Double Sided Tape [HA034].

- 1 x Double Sided Tape [HA033].

- 1 x Metrix Hex Nylon Nut M8.

- 1 x Metrix Hex Nylon Screw M8.

- 4 x Metrix Hex Nylon Nut M2.5.

Battery Block

(H0539-S)

Tail Spacer KIT

(H0540-S)

- 2 x Washer  3x 4.75x0.5.

- 2 x Washer  4.5x 5.9x0.5.

- 2 x Washer  2x 4.5x0.5.

- 2 x Oring ID=2.9, S=1.78.

- 2 x Head Cap Screw M2x6mm.

Plastic Landing Gear

(H0646-S)

- 1 x Plastic Landing Gear SET.

Main Linkage Rod

(H0561-S)

- 2 x Steel Main Linkage Rod.

- 4 x Plastic Ball Link M2.

Plastic Servo Support

(H0548-S)

- 1 x Plastic Servo Support.

- 1 x Head Cap M2.5x18mm.

FBL Support

(H0564-S)

- 1 x FBL Support.

- 2 x Head Cap M2.5x8mm.

- 2 x Tail Fin Stickers.

- 2 x Landing Gear Stickers.

Tail Fin and Landing Gear Stickers

(H0565-S)

Tail Servo Spacer

(H0572-S)

- 4 x Tail Servo Spacer.

- 1 x Center Hub.

- 1 x Socket Head Cap Screw 

        Shouldered M3x16mm.

- 1 x Metric Hex Nylon Nut M3.

Center Hub

[H0595-S]

- 1 x Spindle Shaft.

- 1 x C Washer  5x 5x0.2mm.

Spindle Shaft

[H0596-S]

Yellow/Black Canopy

(H0559-S)

- 1 x Yellow/Black Canopy.

- 1 x Canopy Edge Protection.

- 2 x Canopy Grommet.

Page 35

Chapter 19, Spare Parts

Summary of Contents for 380 KYLE STACY EDITION








































Reviews:

No comments

Brands by name

Popular brands

Load more brands