manualshive.com logo in svg

Goblin 380 KYLE STACY EDITION, User Manual

Share
Download
Goblin 380 KYLE STACY EDITION User Manual Download Page 25

  Approx 474mm  

  5mm  

  5mm  

  13mm  

  13mm  

A

DETAIL A

Carbon Road

Assembly

Plastic 

Ball Link

(H0066-S)

Threaded Rod 

M2.5x40mm

(HC242-S)

Plastic 

Ball Link

(H0066-S)

Socket Head Cap 

Screw M2.5x10mm

(HC022-S)

Finishing 

Washer M2.5

(H0255-S)

Finishing 

Washer M2.5

(H0255-S)

Bag 13

Socket Head Cap 

Screw M2.5x10mm

(HC022-S)

Tail System 

Assembly

Note: Please allow plenty of time for the glue to cure before inserting plastic ball link onto the threaded rod.

Assemble H0040-S in the boom:

Before assembling the two parts in the boom we suggest tightening the 

M2.5 screws into the two plastic parts to pre-thread them. In this way 

when you will assemble the tail servo it will be easier to tighten the screws 

into the plastic parts. Check the tail servo can fit, if necessary carefully sand 

the hole.

Attaching H0082-S to the boom:

Pre-assemble the two boom spacers H0082-S with the M3x20 socket set screw.

Insert into the boom tube completely done up.

Center the holes, then unscrew until there is contact with the walls

Lock everything with the adhesive.

Tail Boom Assembly 

DETAIL A

Threaded Rod 

M2.5x40mm

(HC242-S)

Red/White Tail Boom (H0440-S)

Blue/White Tail Boom (H0443-S)

Carbon Road

4x 2.5x420mm

(HC461-S)

Page 23

Chapter 13, Tail Assembly

Summary of Contents for 380 KYLE STACY EDITION








































Reviews:

No comments

Brands by name

Popular brands

Load more brands