background image

MODEL NO.

B

B3100W

GS-I  BASKETBALL  SYSTEM

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

Ó

2017  Escalade

Ò

Sports

Please  visit  our  World  Wide  Web  site  at: 

www.goalrilla.com

ON-LINE TROUBLE SHOOTING

TECHNICAL  ASSISTANCE

ON-LINE  PARTS  REQUESTS

FREQUENTLY  ASKED  QUESTIONS

ADDITIONAL  ESCALADE®

     

SPORTS  PRODUCT  INFORMATION

2L-7254-03

1. Read  this  manual  carefully  before  starting  assembly. 

Read  each  step  completely

before  beginning  each  step.

2. Some  smaller  parts  may  be  shipped  inside  larger  parts.  Check  inside  all  parts  and

cartons  before  assembling  or  ordering  parts.

3. To  make  assembly  of  your  basketball  system  easier,  use  the  Hardware  Identifier  on

page  3  and  4  to  identify  and  sort  all  fasteners.  Check  all  cartons  for  kits.  All  hardware
is  not  located  in  one  kit.

4. Do  not  tighten  hardware  until  instructed  to  do  so. 

If  hardware  is  tightened  too  soon,

mounting  holes  may  not  align  and  parts  may  not  easily  fit  together.  Leave  locknuts  slightly
loose  until  you  are  instructed  to  tighten  them.

Please  Do  Not  Return  This  Product  to  the  Store!

Contact  Escalade

®

®

®

®

®

  Sports  customer  service  department  at:

Phone:

1-888-USA-GOAL

Toll – Free !

Fax:

1-866-873-3536

Toll – Free !

E-mail:

[email protected]

Mailing  Address:
Escalade  Sports
PO  Box  889
Evansville,  IN  47706

5.

Save this instruction and your proof of purchase (receipt) in the event that the manufacturer

has to be contacted for replacement parts.

O W N E R ' S M A N U A L

Summary of Contents for B3100W

















Reviews: