GO4 Vega I1 Eye One User Manual Download Page 17 | Manualshive

Page: 17 / 19

GO4 Vega I1 Eye One User Manual Download Page 17

GO4 VEGA I1 IP CAMERA USER MANUAL

17

after cruising one hour.

3.5.4 Maintain

Figure 24

Click “Restore factory settings”, a pop up dialog will ask you if you’d like to restore
to factory settings, then the camera will restore factory settings and reboot after
your confirmation.
There are two types software in the camera, one is device firmware, another is
Web UI, and you can upgrade them respectively.

4 Visiting device by other software

4.1 Other web browser

Besides IE browser, you can visit the camera by Firefox, Safari, Chrome, Opera
browser etc., please select “Mode 2 to view”.

4.2 Mobile phone software

For more information, please see the user manual for mobile phone in attached CD,
or download the latest software and user manual in our website.

4.3 Centralization Control

IPCMonitor is a free software offered by factory, several devices on LAN and WAN
can be browsed at the same time. The software also supports snapshot, video
record, scheduled record, alarming and so on. The interface is as figure 25.

«
...
15
16
17
18
19
»

Summary of Contents for Vega I1 Eye One




















Reviews:

No comments