GMR STAMA Evo Operating Instructions Manual Download Page 22

Page: 22 / 26

GMR maskiner a/s

STAMA Micro, Parker, Mini, Multi, Evo, Maxi EL

Lithium batteries

Page 22

Operating Instructions

Battery indicator

If the word SYNCHRONIZE flashes in the display, the battery charge

level reading is invalid. This happens if the indicator has been

disconnected from the battery. Fully recharge the battery to ensure that

the indicator measures correct battery charge level. SYNCHRONISE

disappears from the display.

Displays

Battery
power
(voltage)

Current power

consumption

or charging.

Minus - is

consumption

Ampere hours

used since

charging

Battery

power

remaining (%)

Remaining
operating
hours at
current
consumption

Battery alarm

The battery indicator is set to the relevant size of battery. This must not

be changed except by agreement with GMR.

When the batteries have only a few percent of full power remaining, the

indicator triggers an alarm ((

)), and the truck runs at reduced speed.

The truck should be recharged.

Like an electricity meter, the battery

indicator measures power entering

and leaving the lithium-ion battery.

The battery indicator also calculates

power reserves. The indicator is always

connected to the battery – even when

the main switch is OFF.

CHARGE: Recharge the battery!

Numerical field

Battery charge level

Charging indicator

Battery alarm

Unit of measurement

SYNCHRONIZE: Battery indicator

is not synchronised correctly

10.

Next view

11.

Menu button (not normally used)

12.

Previous view

Summary of Contents for STAMA Evo



























Search results

Summary of Contents for STAMA Evo

Reviews:

Related manuals for STAMA Evo

Brands by name

Popular brands

GMR STAMA Evo, Operating Instructions Manual

Search results

Summary of Contents for STAMA Evo

Reviews:

Related manuals for STAMA Evo

Brands by name

Popular brands